Anyone made their own subwoofer box thats goes under the back seat of an extended cab truck? I got two tens and wanna make the box that holds the subs facing down. Any body got any measurements of their box?
Anyone made their own subwoofer box thats goes under the back seat of an extended cab truck? I got two tens and wanna make the box that holds the subs facing down. Any body got any measurements of their box?
2008 GMC Sierra SLE....370ci LY6 with some goodiesSOLD
1995 C2500- LS1 swap with a mp112
build thread- http://www.ls1truck.com/forums/lsx-t...-ls1-swap.html
Yep, I've got several designs that I have built.
cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
danger_ranger83: I see now why it cost so much to get a harness made... FML
2boostedSilverado: I like Casey's rear end, I want to chat with him about it
Dang nice Duct_tape123!
2013 EC Silverado aka redruM (Just a couple bolt ons.)
2007 RC Silverado aka ?
1998 Trans AM aka Red Dragon
"Your pull your truck to the track on a trailer, I race you with a truck that pulled a trailer to the track."
Hey Duct_tape123 would you recommend using shallow mount woofers with that box?
RUN WAT U BRUNG!!!!
I've got a pair of Rockford Fosgate P3s in the upper box. 1.73 cubic feet with just over 5.75" mounting depth. If the sub doesn't have a wide magnet you could squeeze a 6"+ sub in there. The lower box is 1.23 cubic feet with the same mounting depth but it has a 'recessed' area for my Rockford Fosgate Power1000 5 channel amp. If you can run a full depth sub, do it. You will be much happier with the output.
And thanks for the kind words, guys.
cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
danger_ranger83: I see now why it cost so much to get a harness made... FML
2boostedSilverado: I like Casey's rear end, I want to chat with him about it
NICE!!! thats exactly what i was looking for thank ya
2008 GMC Sierra SLE....370ci LY6 with some goodies
1995 C2500- LS1 swap with a mp112
build thread- http://www.ls1truck.com/forums/lsx-t...-ls1-swap.html
Originally Posted by chvy=power
Looks like I'll have to build the box for the crew cab differently than I usually do. But I already have the design for it =)
1969 Chevy RCLB C10 350/TH400 SOLD
2007 Chevy RCSB 4.8 4x4 LS SOLD
2008 Chevy RCSB 5.3 4x4 LT SOLD
2010 Chevy CCSB 6.2 4x4 LT SOLD
2005 GMC CCLB DRW 6.6 Duramax 4x4 191,000 and counting
2013 FORD CCSB F350 6.7 Powerstroke 4x4
Christian designed the box for my single 10" P3 to fit behind the seat of my truck and it sounds goooood.
2006 SilveradoLittle Black Bitch
Differently how?
Thanks for the kind words
cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
danger_ranger83: I see now why it cost so much to get a harness made... FML
2boostedSilverado: I like Casey's rear end, I want to chat with him about it
You've seen the design. Normally I do them like you do. This is slightly different.Differently how?
Thanks for the kind words
1969 Chevy RCLB C10 350/TH400 SOLD
2007 Chevy RCSB 4.8 4x4 LS SOLD
2008 Chevy RCSB 5.3 4x4 LT SOLD
2010 Chevy CCSB 6.2 4x4 LT SOLD
2005 GMC CCLB DRW 6.6 Duramax 4x4 191,000 and counting
2013 FORD CCSB F350 6.7 Powerstroke 4x4
Posting Permissions
Reply With Quote
