Well I hope this saves someone else some grief. I hate that I have to do this, but Im done with Moser and if I would have known how they operate, I would never have purchased anything from them in the first place....
Let me start, I originally bought the M9 setup from Moser as a complete kit. Fabricated housing, axles, complete center section, brakes... Over $3500 from them for the best parts... I thought... I have been easy on the truck over the last coupe years while working the kinks out, and I finally start pushing it and I end up bending the fabricated 9" housing. My best 60' time was 1.49, and thats the one that bent it, bc after that I could not hook up for some reason....as I checked a few things out after street driving it and it feeling a little off, I found the rear was massively bent.... So I pulled it, and I sent pictures to Moser and get a reply a couple days later with the run around...
This is the actual email conversation with Matt McCombs at Moser. You have to read from the bottom up, You can't see the original email that I sent with the pictures. I just sent the pictures above, and and asked what They thought about it and this is what I got back.
Yes, just the bare housing.
Matt McCombs
Sales Technician
260 . 726 . 6689
mmccombs@moserengineering.com
102 Performance Drive
Portland, Indiana 47371
260 . 726 . 6689
260 . 726 . 4159 fax
www.moserengineering
From: Mic Hubble [mailto:bansheerider44@yahoo.com]
Sent: Thursday, March 01, 2012 8:21 AM
To: Matt McCombs
Subject: Re: Bent m9 pictures
That is just for the housing correct?
Sent from TurboMics iPhone
On Mar 1, 2012, at 7:13 AM, Matt McCombs <mmcombs@moserengineering.com> wrote:
$490
Matt McCombs
Sales Technician
260 . 726 . 6689
mmccombs@moserengineering.com
102 Performance Drive
Portland , Indiana 47371
260 . 726 . 6689
260 . 726 . 4159 fax
www.moserengineering
From: Mic Hubble [mailto:bansheerider44@yahoo.com]
Sent: Wednesday, February 29, 2012 5:24 PM
To: Matt McCombs
Subject: Re: Bent m9 pictures
What is that price?
Sent from TurboMics iPhone
On Feb 29, 2012, at 4:01 PM, Matt McCombs <mmcombs@moserengineering.com> wrote:
I can sell you a rear at distributor pricing.
Matt McCombs
Sales Technician
260 . 726 . 6689
mmccombs@moserengineering.com
102 Performance Drive
Portland , Indiana 47371
260 . 726 . 6689
260 . 726 . 4159 fax
www.moserengineering
From: Mic Hubble [mailto:bansheerider44@yahoo.com]
Sent: Tuesday, February 28, 2012 5:34 PM
To: Matt McCombs
Subject: Re: Bent m9 pictures
Im not sure whats hard to see, thats not an optical illusion, its a straight edge from the flat surface where the center section bolts up out to the tube. So what do you want me to do? Are you just offering to sell me a new one at a discount? I need this thing up and going ASAP. I have a race in April, and still have testing to do. That's why I try to buy the best parts, so I don't have things like this happen. Of all things I thought might fail, this was last on my list. I don't have time to ship this thing to u so u can say " yep it's bent " then offer to sell me a new one. That's just a waste of time. Give me your bottom line up front, I don't have time for games.
If you ask me, it's your housing, that I bought as a complete kit and explained exactly what it was going in to use it in to the sales person when I ordered. I specifically asked if I needed a back brace and was told " no, it was not needed. id never bend this housing, I'd break axles before bending it " now it's bent. I say stand behind YOUR product, and make this right. Let me know ASAP please.
Mic Hubble
Sent from TurboMics iPhone
On Feb 28, 2012, at 4:00 PM, Matt McCombs <mmcombs@moserengineering.com> wrote:
It’s hard to tell exactly, but based on what we can see it may be difficult to straighten. Unfortunately we would be able to have a better idea if we were able to jig it up. That being said if we could work on it we could do it at distributor prices.
Matt McCombs
Sales Technician
260 . 726 . 6689
mmccombs@moserengineering.com
<image001.jpg>
102 Performance Drive
Portland , Indiana 47371
260 . 726 . 6689
260 . 726 . 4159 fax
www.moserengineering
From: Mic Hubble [mailto:bansheerider44@yahoo.com]
Sent: Monday, February 27, 2012 1:10 PM
To: Matt McCombs
Subject: Bent m9 pictures
Maybe Im expecting more than I should, But I believe they should stand behind their product. Im going to try Dutchman now. I have spent lots of money with Moser, But I won't be spending any more with them.
This is where my moser stickers are now as I wait for my new rear end to be built.
Reply With Quote
i can only think of one other place for them, that would be up mosers arse lol 
Originally Posted by RedHeartbeat
